MOXA MGate 5114 Series
1-port Modbus RTU/ASCII/TCP/IEC 101-to-IEC 104 gateways
- Protocol conversion between Modbus RTU/ASCII/TCP, IEC 60870-5-101, and IEC 60870-5-104
- Supports IEC 60870-5-101 master/slave (balanced/unbalanced)
- Supports IEC 60870-5-104 client/server
- Supports Modbus RTU/ASCII/TCP master/client and slave/server
- Effortless configuration via web-based wizard
- Status monitoring and fault protection for easy maintenance
- Embedded traffic monitoring/diagnostic information for easy troubleshooting
- microSD card for configuration backup/duplication and event logs
- Built-in Ethernet cascading for easy wiring
- Redundant dual DC power inputs and relay output
- -40 to 75°C wide operating temperature models available
- Serial port with 2 kV isolation protection
- Security features based on IEC 62443
The MGate 5114 is an industrial Ethernet gateway with 2 Ethernet ports and 1 RS-232/422/485 serial port for Modbus RTU/ASCII/TCP, IEC 60870-5-101, and IEC 60870-5-104 network communications. By integrating commonly used power protocols, the MGate 5114 provides the flexibility needed to fulfill the various conditions that arise with field devices that use different communications protocols to connect to a power SCADA system. To integrate Modbus or IEC 60870-5-101 devices onto an IEC 60870-5-104 network, use the MGate 5114 as a Modbus master/client or IEC 60870-5-101 master to collect data and exchange data with IEC 60870-5-104 systems.
Easy Configuration via Web Console
The MGate 5114 Series comes with an illustrated Quick Setup guide designed to make configuration easy. With Quick Setup, you can easily access protocol conversion modes and finish the configuration in a few steps.
Modbus RTU/ASCII/TCP Protocol Traffic Monitor
MGate 5114 Series gateways support Modbus RTU/ASCII/TCP, IEC 60870-5-101, and IEC 60870-5-104 Protocol Traffic Monitor for easy troubleshooting, especially during the installation stage. It is worth mentioning that traffic logs can be viewed in the popular troubleshooting tool, Wireshark. With this feature, you can easily analyze traffic to determine the root cause of a problem.
Maintenance Functions
MGate 5114 gateways support a system log function that records events in the MGate; users can easily review log data remotely through the web console. The gateways also support status monitoring and fault protection functions. The status monitoring function notifies a PSCADA system when a device gets disconnected or does not respond, in which case the PSCADA system gets the status of each end device and then issues alarms to notify operators.
Specification
- Ethernet Interface
- 10/100BaseT(X) Ports (RJ45 connector)
2
Auto MDI/MDI-X connection
Magnetic Isolation Protection
1.5 kV (built-in)
Ethernet Software Features
- Industrial Protocols
Modbus TCP Client (Master), Modbus TCP Server (Slave), IEC 60870-5-104 Client (Master), IEC 60870-5-104 Server (Slave)
Configuration Options
Web Console (HTTP/HTTPS), Device Search Utility (DSU), Telnet Console
Management
ARP, DHCP Client, DNS, HTTP, HTTPS, SMTP, SNMP Trap, SNMPv1/v2c/v3, TCP/IP, Telnet, SSH, UDP, NTP Client
MIB
RFC1213, RFC1317
Time Management
NTP Client
Serial Interface
- Console Port
RS-232 (TxD, RxD, GND), 8-pin RJ45 (115200, n, 8, 1)
No. of Ports
1
Connector
DB9 male
Serial Standards
RS-232/422/485
Baudrate
50 bps to 921.6 kbps
Data Bits
7, 8
Parity
Even, Mark, None, Odd, Space
Stop Bits
1, 2
Flow Control
RTS Toggle (RS-232 only), RTS/CTS
RS-485 Data Direction Control
ADDC® (automatic data direction control)
Pull High/Low Resistor for RS-485
1 kilo-ohm, 150 kilo-ohms
Terminator for RS-485
120 ohms
Isolation
2 kV (built-in)
Serial Signals
- RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422
Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w
Data+, Data-, GND
RS-485-4w
Tx+, Tx-, Rx+, Rx-, GND
Serial Software Features
- Industrial Protocols
Modbus RTU/ASCII Master, Modbus RTU/ASCII Slave, IEC 60870-5-101 Master (Balanced/Unbalanced), IEC 60870-5-101 Slave (Balanced/Unbalanced)
Configuration Options
Serial Console
ModbusRTU/ASCII
- Mode
Master, Slave
Functions Supported
1, 2, 3, 4, 5, 6, 15, 16, 23
Max. No. of Commands
128
ModbusTCP
- Mode
Client, Server
Functions Supported
1, 2, 3, 4, 5, 6, 15, 16, 23
Max. No. of Client Connections
32
Max. No. of Server Connections
32
Max. No. of Commands
128
IEC 60870-5-104
- Mode
Client (Master)
Server (Slave)
Max. No. of Client Connections
32
Max. No. of Server Connections
32
Max. No. of Information Objects
2000 points
IEC 60870-5-101
- Mode
Master (Balanced/Unbalanced)
Slave (Balanced/Unbalanced)
Max. No. of Master Connections
1
Max. No. of Slave Connections
1 (Balanced), 31 (Unbalanced)
Max. No. of Information Objects
2000 points
Memory
- microSD Slot
Up to 32 GB (SD 2.0 compatible)
PowerParameters
- Input Voltage
12 to 48 VDC
Input Current
455 mA @ 12 VDC
Power Connector
Screw-fastened Euroblock terminal
Relays
- Contact Current Rating
Resistive load: 2 A @ 30 VDC
PhysicalCharacteristics
- Housing
Metal
IP Rating
IP30
Dimensions
36 x 105 x 140 mm (1.42 x 4.14 x 5.51 in)
Weight
507 g (1.12 lb)
EnvironmentalLimits
- Storage Temperature (package included)
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Operating Temperature
MGate 5114: 0 to 60°C (32 to 140°F)
MGate 5114-T: -40 to 75°C (-40 to 167°F)
Standardsand Certifications
- Safety
EN 60950-1, UL 508
EMC
EN 55032/24
EMI
CISPR 32, FCC Part 15B Class B
EMS
IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000-4-4 EFT: Power: 4 kV; Signal: 2 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 10 V/m; Signal: 10 V/m
IEC 61000-4-8 PFMF
Hazardous Locations
ATEX, Class I Division 2, IECEx Class 1 Division 2, ATEX, and IECEx certifications are underway.
Please contact us for details.
Freefall
IEC 60068-2-32
Shock
IEC 60068-2-27
Vibration
IEC 60068-2-6, IEC 60068-2-64
MTBF
- Time
1,140,815 hrs
Standards
Telcordia SR332
Kunden, die diesen Artikel gesehen haben, sahen auch